Intelligent Wireless Riggers Remote
The
focusBrain XL is a wireless DMX-512 riggers remote control. The 19"
base unit is connected
between
the
DMX output of the control desk en the DMX input of the dimmers. With the
remote, you can call up any
combination
of channels at any value. The DMX output
signal is merged with the DMX input, so the lighting
control
desk and the remote can
be active at the same time. In addition, 50 memories can be stored
and
recalled,
they can even be given a cross fade
time.
Applications:
Theater
(lamp focusing)
Lighting
desk remote (via the DMX input of the desk)
Stand
alone operation (using the 50 memories)
Options:
Additional
product firmware can be loaded in the base unit to directly control
other
brands
of lighting control desks, like: ADB / Strand / Jands / Avab
Specifications:
512
channel DMX control (selectable 1-512 or 513-1024)
Merging
DMX input and remote control in HTP (highest takes precedence)
50
scenes memory
Memory
capture from the DMX input
HF
range indoors 50 - 70 meters
External
active antenna
RS-232
port for lighting desk control (special firmware required)
| ELC Lighting - Focus
Hand 3 |
|
Wireless
DMX Riggers Remote
The
focusHAND 3 is a simplified version of the focusBRAIN XL. It has
the same wireless handheld
remote.
It
allows you to call up any combination of channels at any value.
The DMX output
signal is merged with the
DMX
input, so the lighting control desk and the remote can be active
at the same time. In
addition 50
memories
can be stored and recalled. The base unit is
connected between the DMX output of the lighting
control
desk and
the DMX input of
the dimmers.
Applications:
Theatre
(lamp focusing)
Rental
Specifications:
512
channel DMX control (selectable 1-512 or 513-1024)
HF
range indoors 50 - 70
Activation
via handheld remote
|
ELC Lighting DMX
Over Ethernet Tools
| ELC Lighting - dmXLAN
node8GB / node8s |
|
The
dmXLAN node8GB and node8s have 8 fully programmable DMX ports
and 2 ethernet ports that work
either
in Gigabit or 100mBit. It is a first-of-its-kind node that is
fitted with a 2 port Gigabit switch. 8 fully
programmable
DMX ports make the Node 8GB much more than just a DMX to
Ethernet and Ethernet to
DMX
node: It is also splitting, merging, dispatching, softpatching,
backing up ....You name It!
Like
all the ELC node range, this unit is fully
compatible and programmable through our dmXLAN Software
Connections:
2x
10/100/1000 MBit Ethernet connection on Neutrik Ethercon
(integrated switch)
8x
Bi-Directional DMX ports on Female XLR5-pin.
DMX
ports can be used for DMX
output, DMX input or DMX
output with RDM |
| ELC Lighting - dmXLAN
node6x |
|
6-Port DMX / Ethernet node
with integrated 5-port Switch
dmXLAN
node6x is our top all in one DMX / Ethernet solution.
It features 6x DMX input/output
ports, fully
compatible
with our free dmXLAN
software with advanced DMX channel merging & patching, and a
5-port
10/100MBit
Ethernet switch. It also
works perfectly as a standalone DMX toolbox.
Features:
Remote
programming and monitoring
DMX
input options like Normal and Backup
DMX
output options like:
-
Normal
-
Merging in HTP / LTP or custom
-
Priority merging
-
Merging with softpatch
Remote
takeover of fixture parameters
Visualizer
input supports software like WYSIWYG / ESP / Capture / and many
others
Connections:
3x
10/100 mBit Ethernet connection on Neutrik Ethercon (Front)
2x
10/100 mBit Ethernet connection on RJ45 (Back)
6x
Bi-Directional DMX ports on Female XLR5-pin.
DMX
ports can be used for DMX
output, DMX input or DMX
output with RDM (Front) |
| ELC LIghting - dmXLAN
node8 |
|
8/2 Port DMX / Ethernet interface with
enhanced merging and control
dmXLAN
node 8 is our top of the range DMX to Ethernet and Ethernet to
DMX node
It
features 2x fixed DMX inputs & 8x DMX inputs/outputs ports ,
fully compatible with our
free
dmXLAN software with advanced DMX channel merging &
patching. It also works
perfect
as a standalone DMX toolbox.
Features:
Remote
programming and monitoring
DMX
input options like Normal and Backup
DMX
output options like:
-
Normal
-
Merging in HTP / LTP or custom
-
Priority merging
-
Merging with softpatch
Remote
takeover of fixture parameters
Visualizer
input supports software like WYSIWYG / ESP
/ Capture / and many others
Connections:
10/100
mBit Ethernet connection on Neutrik Ethercon
8x
Bi-Directional DMX ports on Female XLR5-pin.
The
DMX ports can be used for DMX output, DMX input or
DMX output with RDM
2x
DMX input ports on Male XLR5-pin
Midi
In/Out
RS232
4x
Contact closure Input (for calling up configurations)
|
| ELC Lighting - dmXLAN
switch8LX |
|
10/100
mBit ethernet switch/distributor with optimized
programmable
switching engine and real-time backup loop
There
are 4 configurations:
8x
CAT5 10/100mBit Ethernet ports on Neutrik Ethercon
6x
CAT5 10/100mBit Ethernet ports on Neutrik Ethercon, and
2x Fiber optic 100MBit ports
(ports
1 & 2) on SC connector
8x
CAT5 10/100mBit Ethernet ports on Neutrik Ethercon, with Power Over Ethernet on ports 3
to 8.
6x
CAT5 10/100mBit Ethernet ports on Neutrik Ethercon, and
2x Fiber optic 100MBit ports
(ports
1 & 2) on SC connector, with
Power Over Ethernet on ports 3 to 8
Features:
Real-Time
backup loop: Create a ring of switches. if a cable/connection
fails, then the signals are directly
rerouted
(the show can/must go on). a message is displayed in the dmXLAN
software
Multicast
filtering: routing of multicast protocols on a port base
(example MA-net/ACN/digital audio)
Artnet
Filtering: setup a port to filter the artnet universes. This is useful
for low bitrate connections like
wireless
or 10mBit equipment. The port will only pass thru enabled
universes
Cable
testing: if there is a problem in a UTP cable, the switch can
test the cable and tell you where the
problem
is (up to 80cm accuracy)
|
| ELC Lighting - dmXLAN
node3 TM |
Our
DMX to Ethernet Nodes range is extended by this very smart
unit: It is the first unit on the market
featuring
2 Ethernet port ( a mini Ethernet switch is included) and 3
DMX port. dmXLAN node3 is a
versatile
DMX to ethernet node with an added ethernet switch.
It
features 3x DMX input/output ports, fully compatible with
our free dmXLAN software
with advanced
DMX
channel merging & patching. It also works perfectly
as a standalone DMX toolbox.
Features:
Remote
programming and monitoring
DMX
input options like Normal and Backup
DMX
output options like:
-
Normal
-
Merging in HTP / LTP or custom
-
Priority merging
-
Merging with softpatch
Remote
takeover of fixture parameters
Visualizer
input supports software like WYSIWYG / ESP / Capture / and many
others
Connections:
2x
10/100 mBit Ethernet connection on Neutrik Ethercon
3x
Bi-Directional DMX ports on Female XLR5-pin.
DMX
ports can be used for DMX
output, DMX input or DMX
output with RDM
Available
in normal and Full Isolated ( FI ) version. Also available as:
Wall mount and Surface mount
|
|
ELC Lighting - dmXLAN
node3 WM
|
|
Easy
install 3 Port wall mount DMX / Ethernet interface with added
ethernet switch
dmXLAN
node 3WM is a wall mount 3 DMX ports (in or out) with 2 Ethernet
ports and power supply
thru
PoE (Power over Ethernet). The node3 if fully compatible with
our free dmXLAN software
(see
software section). The 3 DMX ports can be fitted with male or
female connectors.
A
large display will allows the programming on spot of the main
parameters
Features:
3
DMX ports (act as input or output)
Internal
10/100mBit Ethernet port on the PC board, allowing PoE ( Power
over Ethernet)
External
10/100mBit Ethercon port on the wall plate, with the 3 DMX ports,
giving a full access network.
Internal Ethernet switch.
Remote
programming and monitoring
DMX
input options like Normal and Backup
DMX
output options like:
-
Normal
-
Merging in HTP / LTP or custom
-
Priority merging
-
Merging with softpatch
Remote
takeover of fixture parameters
Visualizer
input supports software like WYSIWYG / ESP / Capture / and many
others
Options:
Selection
of XLR connectors, Male or Female
Wall
mount version
Surface
mount version
ELC Lighting - dmXLAN
node3 SM
|
|
ELC Lighting - dmXLAN
node1s
|
|
Easy
install single Port wall mount DMX / Ethernet interface
dmXLAN
node1s is a wall mount 1 DMX port (in or out) with 1 Ethernet
port and power supply thru
PoE
(Power
over Ethernet). The node1 if fully compatible with our free
dmXLAN Software (see
software section
at
the ELC Lighting Website).
The 1 DMX port can be fitted with a male or female connector.
Features:
1
DMX port (act as input or output)
Internal
10/100mBit Ethernet port on the PC board, allowing PoE ( Power
over Ethernet)
Remote
programming and monitoring
DMX
input options like Normal and Backup
DMX
output options like:
-
Normal
-
Merging in HTP / LTP or custom
-
Priority merging
-
Merging with softpatch
Remote
takeover of fixture parameters
Visualizer
input supports software like WYSIWYG / ESP / Capture / and many
others
Options:
Selection
of XLR connectors, Male of Female
|
| ELC Lighting - dmXLAN
switch5 |
|
5-port 10/100 mBit ethernet
switch/splitter with Power over Ethernet supply
Specifications:
Truss
mount housing with built-in M10 nut and safety eye
4x
10/100 BaseT ports on Neutrik Ethercon connector with
PoE (Power on Ethernet) among
IEEE
802.3af with auto-detection, for powering
our DMX Nodes
1x
10/100 BaseT uplink port on Neutrik Ethercon connector
All
ports are auto crossing MDIX (no cross cables needed)
5
LEDS indicating link when on and data presence when blinking
|
ELC Lighting - DMX Show
Recording Tools
| ELC Lighting - showStore
XLan |
|
2048 channel DMX / Ethernet showrecorder
and programmable playback
The
showSTORE XLan can record 99 shows with up to 2048 DMX-channels
via DMX and ArtNet/Ethernet.
The
playback can be controlled by front panel / contact closure
input / RS-232 / midi / DMX / real-time
clock
/ timecode or build in customizable web-server. The showSTORE
XLan is fully compatible with
our
dmXLAN software with the advanced channel merging and patching.
The files can be exchanged
via
the USB port, the showSTORE acts as an external drive.
Applications:
Museums
Architectural
Shop windows
Exhibitions
Rental
Control
Operation:
Local control
Contact closures
RS-232
MIDI
SMPTE timecode
Internal clock with date and time
Built in web server with custom web pages
AC612XL
Specifications:
2x DMX input ports
2x DMX output ports
2048 channel (thru ethernet)
10/100 mBit Ethernet on Neutrik Ethercon connector
RS-232
4x Contact closure inputs
MIDI in / out
Timecode input
|
| ELC Lighting - miniStore
3 |
Small 512 channel dynamic DMX-512 show
recorder / playback, with USB.
The
miniStore is a reduced version of the showStore XLan. It is able
to record one DMX show in real
time from any DMX
lighting desk with up to 512 channels. The show file can be
exchanged via the USB
connector, and is file
compatible with show files of the showStore XLan.
Applications:
Exhibition stands
Museums
Shopping displays
Operating
modes:
Normal playback and recording
Playback only, write protected
Single shot playback by contact closure
Power on playback loop
Specifications:
512 DMX channels
Available in 5 and 3 pin versions
Nonvolatile record memory 1GB SD
|
ELC Lighting - DMX Control
Boards
|
This
new version of our popular AC612 range stores 12 scenes
of 512 DMX channels from the DMX input.
You can recall them with a button. A master fader ( UP / DOWN
buttons) allows control of all the scenes
from
0% to 200%. USB port allows firmware upgrade for future added
functions.
With
the latest version 2.x and Editor
Software it now supports multiple scenes per
button.
Specifications:
Power: 8-30Vdc , 200mA
Size: 180mm x 80mm x 23mm
|
|
This new version of our popular AC612 range
stores 5 scenes of 512 DMX channels from the DMX input.
You can recall them with a fader. A master fader ( UP / DOWN
buttons) allows the control of all the scenes
from 0% to 200%. USB port allows firmware
upgrade for future added functions.
With the latest version 2.x and Editor
Software it now supports multiple scenes per fader.
Specifications:
Power: 8-30Vdc , 200mA
Size: 180mm x 80mm x 23mm
|
| ELC Lighting - AC612
XUDin |
|
This new version of our popular AC612 range
stores 12 scenes of 512 DMX channels from the DMX input.
You can recall them with a contact closure. USB port allows
firmware upgrade for future added functions.
With the latest version 2.x and Editor
Software it now supports multiple
scenes per contact.
Specifications:
• Power: 8-30Vdc , 200mA
• Size: standard DIN housing
|
| ELC Lighting - sideKick
too |
|
The
sideKick too is based on the AC612XU control. It has 30
playbacks, each capable of running multiple
stepped
memories. The 20 buttons on the top are playbacks 1 to 20 and
the faders with flash buttons are
playbacks
21 to 30. Single step memories can be created by capturing the
DMX input, and multiple step
memories
are created via the AC612 Editor Software.
On
the back there is a DMX input and DMX output with internal DMX
merge and a USB connector used
for
PC/Mac connection or power (shipped with USB power supply)
In addition to the AC612XU functions,
the
unit can also act as a DMX wing via the DMX output. Or via a special
interface software to remote
GrandMa
on PC |
ELC Lighting - DMX Distribution Tools
ELC Lighting - High speed Merger DT-221 mkII
High speed DMX signal merger
The DT-221mkII is a table top DMX signal merger that combines two DMX sources into one DMX signal.
The merging can be done in one of 3 ways:
HTP merge: The highest value of a channel is the DMX output
LTP merge: The last changed channel value is the DMX output
Priority merge: DMX input A has priority over input B. If input A fails, the unit switches to DMX input B.
The signal delay between DMX input A and DMX output is only 50 micro-seconds (0.00005 sec).
Applications:
"Mixing" of 2 DMX lines for:
Touring
Theater
Backup
Light Rental
Options:
3 pin or 5 pin XLR connections
19"-rackmount kit
| ELC Lighting - DMX/RDM
Splitter DT2210 |
|
DT2210
DMX splitter with RDM support.
2
Inputs on the Back.
10
Outputs on the Front, with Source selection per 2 Outputs.
Available
in Normal and Full Isolated.
Available
with 5 pin and / or 3 pin XLR.
|
| ELC Lighting - Splitter
DT-229 RDM |
|
2
in 9 out RDM Compatible DMX Splitter
RDM
Compatible
2
DMX inputs, opto isolated
8
outputs on the front panel with A / B selector for the 2 inputs
Output
9 on the rear for a direct link to the dimmer
Available
as fully isolated version DT 229FI, where the front 8 outputs
are also opto isolated
19"
rack mount cabinet
Universal
power supply 90V to 240V AC
|
ELC Lighting - Splitter DT-125 RDM
1 in 5 out RDM compatible DMX Splitter
- RDM compatible
- 1 DMX input, opto isolated
- 5 outputs on the front
- bi-color LED for signal / error indication (even from long distance)
- available as full isolated (DT125-FI), where the 5 outputs are also opto isolated
- table top/truss mount cabinet with M10 bold and safety eye
- 19" rackmount kit available
- Universal power supply 90V to 240V AC
Accessory
19"
mounting kit
|
